Pigtail Bolt M16 used on wooden, concrete and other power poles for supporting clamps and at the consumer’s premises. The clamps corrosion resistance conforms to the standards.Bolts and nuts is made of hot dip galvanised steel. Ultimate Tensile strength (UTS) of the clamp is 20KN.
Contact Now
Eye bolts is manufactured from steel, strength designation 4.6 and meet the requirements for mechanical properties.The safe working load of any eye bolt is that load which may be safely carried in an axial direction.
Contact Now
Hook bolt made of Q235B galvanized steel, with good high strength mechanical strength, long term usage in optical fiber cable installation, FTTH networks and aerial ADSS accessories.Technical property:1. performance class:4.6 2. The nominal tensile strength of the bolt material reaches 400Mpa3. The yield ratio of the bolt material is: 0.64. The nominal yield strength of the bolt material is up to 400×0.6=240MPa
Contact Now
U bolt has high strength and corrosion resistance and is widely used in power industry.Features:1. Carbon steel material, corrosion resistance, high hardness, not easy to deform2. Hot dip galvanized zinc coating for increased corrosion resistance and longer life3. The thread & pitch can be made according to different standard
Contact Now
The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble:
Contact Now
Square flat washer with 17.5mm diameter hole for 5/8" diameter bolt. Galvanized per ASTM A-153.Features:1. Material: steel2. Finish: galvanized3. Usage: for 5/8” bolts. Technical specification:
Contact Now
PVC insulation piercing connector It is suitable for the branching and splicing of overhead insulated wires of 1kV and below. Features:Fully insulated housingStructure sealed, waterproof, anti-corrosion, long lifePuncture structure, torque bolt, ensure puncture pressureDifferent diameter and different wire connection, strong applicability.Model No.Suitable conductor range sqmmMain dimensionsqmmNormal current(A)Bolt noMain lineSub lineABHJBC1/7010-7015-10412355551JBC1/9516-951.5-10412655551JBC-116-12016-1206049802991JBC-250-24050-2407484.51164762
Contact Now
TJ brass bolts are suitable for connection in power transmission and distribution lines. The red copper material has good electrical conductivity and high resistance to electrical resistance. The bolt design guarantees constant contact pressure; the surface is smooth, without burrs, making the work more stable and calm.
Contact Now
The Bolts, eye bolts, eye nuts and Nuts is manufactured by Hot/Cold forging process neatly and cleanly finished and have metric threads.Eye bolts threads is throughout their length and bolts threads is at 60% of their length.All the materials have bright surface finish. composition:1.The plain washers is cold punched2.Individual nuts and eye nut is used for special purposes, such as lock nuts.3.Before dispatch from the works one washer is fitted to each bolt, eye bolt, eye nut and a nut is screwed on the whole threaded length and left in this position.4.Each set of bolt and nut includes o
Contact Now
The NLL wedge-shaped strain clamp has the advantages of very small hysteresis loss, light weight, and convenient installation, which meets the requirements of energy saving and consumption reduction in the transformation of the national grid. The main body of the product is made of aluminum alloy, and the bolts and nuts are made of hot-dip galvanized material.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-24. U bolt number: 2 nos M125. Tension strength: 50kNTechnical specification: Model1KV Overhead Insulated wir
Contact Now
M16 eye nut is made of carbon steel hot-dip galvanized material, with a smooth surface, which can resist corrosion and rust in a humid environment. Solid design, thick material, durable and long service life. The internal thread is deep, the force is even, the screw teeth are sharper, and it is not easy to slip during the rotation.
Contact Now
PAL1500 aluminum wedge dead end clamp is used to insulate neutral wire suspension cross-bonded cables(25sqmm to 70sqmm). It can use CS-10 aluminum alloy pole mounted bracket for fix, also can be bolted to the pole with M14&M16 bolt or two stainless steel straps 20mm×0.7mm. Black wedge and wire bail to identify insulated neutral clamp.Features:1. Material: high strength aluminum alloy.
Contact Now
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized
Contact Now
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized
Contact Now
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized
Contact Now
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized
Contact Now
Square curved washer with 7/8" diameter hole for 3/4" diameter bolt. Galvanized per ASTM A-153.Features:1. Material: steel2. Finish: galvanized3. Usage: for bolts. Technical specification:
Contact Now
Rag bolts conforms with BS 1494, except that the bolts shall be 72mm long and they are supplied with M10 thread, coarse pitch, free fit.Each bolt is supplied with one full nut.Features:- Tensile strength: 352 N / mm2- Elongation (break): 33%- Code bending: 180°Measures:- Diameter: 10mm- Length: 72mm- Thickness of tube: 0.6mm- Unit weight: 21gramPackaging:Resistant cardboard box with the customer information in the visible part of the box. TECHNICAL SPECIFICATION: SpecificationLengthQuantity per cartonUnit weight gramWeight per carton(kg)10
Contact Now
The turnbuckle bolts are expanded and contracted by the lead screw, which can adjust the tightness of the wire rope. The components can be bundled during component transportation and loosened during installation and correction.1.Types: turnbuckle bolt, open body turnbuckle2.Material: Q235B steel 3.The main purpose: to adjust the tightness of the wire rope, and it is widely used.4.Features: simple structure, easy processing, low cost, and strong practicability.
Contact Now
The aluminum alloy suspension clamp is firm, easy to install, sturdy and durable, and adopts low-pressure casting technology; it has strong corrosion resistance, no hysteresis, not easy to break, and strong electrical conductivity. Features:1. Material: high strength alloy aluminum2. Model No.: XGH-33. U bolt number: 2 nos bolts4. Tension strength: 40kNTechnical specification: modelAdapt to wire diameter(mm)Main dimensions(mm)Nominal failure load(KN)reference weight(kg)HCMRLXGH-25.1~12.552.5251618.0166401.0XGH-312.4~1750.5231611.5200401.5XGH-419~23.559.5271613.522
Contact Now
The hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Contact Now
The pole clamp is suitable for connecting the tension suspension clamp and the electric pole. Features: 1. Product manufacturing is strictly controlled and meets production standards. 2.The surface of the product has no burrs and is relatively smooth. 3. Support customization of a variety of special-shaped productsThe hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Contact Now
The thimble clevis is mainly for ADSS light span tension set which made of galvanized ductile iron.All dielectric dead-ends require a proper size and strength thimble clevis or extension link.Technical characteristics:Model No.: TC-02Associated Bolt size: M14Tension strength: 20KNFinish: hot dip galvanized steelCotter pin: stainless steelDrawing: Installation image(part 2):
Contact Now