LV Stay Assembly 11KV-manufacture,factory,supplier from China

(Total 24 Products for LV Stay Assembly 11KV)
The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble: 
  Contact Now
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized 
  Contact Now
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized 
  Contact Now
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized 
  Contact Now
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized 
  Contact Now
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
  Contact Now
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled.  All ferrous part is made in hot dip galvanized.
  Contact Now
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
  Contact Now
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment.  top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image: 
  Contact Now
The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image: 
  Contact Now
The galvanized steel strand is made of galvanized material and is composed of multiple steel wires. It has strong anti-rust, anti-rust ability, corrosion resistance, strong load-bearing, and good toughness. After multiple tensile tests, each steel wire rope has no breaks and no loose strands. The surface is smooth, burr-free, high tensile strength, and small bending radius.
  Contact Now
The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand.  The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm(L×W×H)Installation image: Drawing: 
  Contact Now
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
  Contact Now
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
  Contact Now
A hoop is a component that uses one material to hug or hoop another material, which is a fastener. There are many types of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless steel hoops are more commonly used.Technical specification table: 
  Contact Now
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
  Contact Now
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
  Contact Now
APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.
  Contact Now
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Contact Now
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
  Contact Now
Suspension clamps for optical cables are made of real materials, with stable performance and long service life. Composed of insulating clamps and connecting buckles, the stress distribution is even, there is no concentrated point, it can enhance the rigidity of the cable installation point, and the protection performance of the optical cable is good. It has a larger contact area with the optical cable and is equipped with flexible rubber clamps to enhance self-damping and reduce wear.
  Contact Now
Alloy aluminum anchoring bracket CS1500 is a kind of fixed clamp for cable poles, made of cast aluminum alloy. The aluminum alloy telegraph pole bracket produced by our company has a smooth and flat surface, rounded and smooth corners, flat and no roughness, fine workmanship, and durability. Features:1. Breaking load: 10kN2. Package:50 pieces3. Gross weight: 10 kg4. Dimension: 47×31×17cm5. Material: high strength alloy aluminum 
  Contact Now
NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125~7010~255.0~10.02M1240NLL-250~120
  Contact Now
Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.
  Contact Now
Relate News
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
The standard plywood crates customized based on requirements of customers and loaded in the container.
We sent our bolts samples to the National space frame and steel structure quality supervision and inspection center, the samples were tested and meet the technical requirements of standard GB/T 2694-2010 and GB/T 3098.1-2010. 
Electricity is the most indispensable energy source in our lives. Without it, our lives will fall into a mess, and it is the high-voltage wires that ensure that the electric energy reaches our living places safely. In the past, when technology was not so advanced, wires were pulled from the sky to every household, so many small counties still have many cables between houses. In cities, more are buried underground, which can be more secure. However, in many heavy industrial areas, high-voltage wires still need to be passed through high-altitude.
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.
1.extensive variety of applications, torsion resistance and pressure resistance, balanced torsion torque, company and tight locking, and huge adjustment variety. 2.put it at the telegraph pole, tighten and fix it. 3. the poles with diameters of one hundred seventy five-197mm can be adjusted. Pole clamp belt for cable garage bracket is manufactured from c201 stainless-steel, with width of 19mm, thickness of 0.7mm and duration from 1.2m to at least one.5m primarily based on exclusive pole.