Joint Compression-manufacture,factory,supplier from China

(Total 24 Products for Joint Compression)
A compression type mid-span joint consists of the following parts:a. Aluminium alloy tube for aluminium alloy conductors.b.
  Contact Now
CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.
  Contact Now
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
  Contact Now
ADSS optical cable suspension clamp components: 1.Aluminum clamp:made of corrosion-resistant aluminum alloy pressure casting, the aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties. 2.Rubber clamp:Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 3.Bolts, flat washers, spring washers, nuts, closed pins, U-shaped hanging rin
  Contact Now
The preformed strain clamp is used to bear full tension on the bare conductors and overhead insulated conductors in the power transmission and distribution line, and connect the conductors to the strain tower, which can replace the conventional bolt-type strain clamp and compression type strain Clamps and wedge-shaped strain clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the
  Contact Now
Material 1. Rubber Clamps Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 2. Aluminum splint It is made of corrosion-resistant aluminum alloy by pressure casting. The aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties.
  Contact Now
The preformed strain clamp is used to undergo full anxiety on the naked conductors and overhead insulated conductors in the energy transmission and distribution line, and connect the conductors to the stress tower, that could replace the traditional bolt-type stress clamp and compression kind strain clamps and wedge-shaped stress clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the produ
  Contact Now
Features: a. Even stress distribution, no stress concentration point, can well protect the optical cable. b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension. c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is fully suitable for the needs of optical cable erectionProduct composition diagramProduct technical specification sheet:  Sn Model No.
  Contact Now
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
  Contact Now
The preformed tension clamp for the conductor is connected to the tower by its matching fittings, such as insert ring, bowl-head hanging plate, etc., which can replace conventional bolt-type tension clamps, compression-type tension clamps and wedge-type tension cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wire: aluminum-clad stee
  Contact Now
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
  Contact Now
According to the size of the object to be bound, it can be cut to any desired length, equipped with stainless steel buckles, and quickly installed with the corresponding strap tightening machine, which is safe, fast and reliable.Material: cast steelSuitable for width of band strap: 9.5-25.0mm Suitable for thickness of band strap: 0.8-1.0mmSurface treatment: sprayed, chrome platedOur tension tool for SS strapping band with the advantages below: 1.It has a wide range of applications and multiple uses.
  Contact Now
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 
  Contact Now
Structural features: 1.The anti-vibration rod will not cause the stress concentration of the wire, nor damage the wire, to avoid corrosion or arcing. 2.The spiral anti-vibration rod is composed of a short gripping section and a long damping section. 3.The gripping section can effectively hold the cable and firmly fix it on the cable.
  Contact Now
ADSS optical fiber cable insulation wedge clamp is a kind of ADSS optical cable clamp. Mainly used for optical cables with 6-9mm cable diameter. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 173×65×40mmUnit weight:190gCarton size: 550×410×250mmQuantity per carton : 100 piecesMaterial: Nylon and stainless steelCable diameter: 6-9mm Installation image: 
  Contact Now
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Contact Now
The OPGW grounding clamp consists of a section of aluminum alloy wire, an aluminum alloy clamp (connected to the OPGW optical cable), and all-aluminum terminal blocks (connected to the main material of the iron tower).
  Contact Now
The protective rod is divided into FYB and FYH types.
  Contact Now
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
  Contact Now
The structure of the preformed armor rod and the short protective rod is simple. A set of pre-twisted wires form an empty tube, which generates a gripping force when wrapping the wire, thereby protecting the wire. The pre-twisted wire protection line is used for vibration protection and has been included in the hardware products.
  Contact Now
The repair sleeve comprises of two pieces with a provision of seat for sliding of the keeper piece.
  Contact Now
PAL1000 aluminum alloy optical cable insulation strain clamp is a product suitable for overhead insulated conductors. The product is used for cable pull, aluminum alloy body material, PA66 insulation core, stainless steel wire rope, and the product process is die-casting. The high-quality aluminum alloy material has strong corrosion resistance and is not easy to rust and age. The appearance is neat and tidy, and the unique design can well protect the cable.Features:1. Material: high strength aluminum alloy.
  Contact Now
NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125~7010~255.0~10.02M1240NLL-250~120
  Contact Now
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
  Contact Now
Relate News
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.
1.1 puncture structure, easy installation, no need to peel insulated wire; 1.2 moment nut, constant puncture pressure, ensure good electrical connection without damaging wire; 1.3 self sealing structure, moisture proof, water proof, corrosion proof, extend The service life of insulated conductors and clamps 1.4 use special contact blade, suitable for copper (aluminum) Butt joint and copper-aluminum transition 1.5 electrical contact resistance is small, contact resistance is less than 1.1 times of resistance of equal length branch wire, dL/T765.1-2001 standard 1.6 speci
Tools/raw materials Aluminum alloy joint box Pre-twisted suspension clamp Optical cable down lead clamp Cable rack Tower fastener Cable hoop Whip and hammer Pre-twisted hardware1.Before installing the inner twisted wire, pass the outer twisted wire through the embedded ring and make it parallel to the optical cable, and mark the optical cable where the outer twisted wire is colored.2.Winding the first group of inner twisted wires on the optical cable; Align the second group of inner twisted wires with the first group of inner twisted wires, winding the s
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
We sent our bolts samples to the National space frame and steel structure quality supervision and inspection center, the samples were tested and meet the technical requirements of standard GB/T 2694-2010 and GB/T 3098.1-2010.