Connectors-manufacture,factory,supplier from China

(Total 24 Products for Connectors)
Copper tube butt connectors, also known as copper tube splices, are used for connecting wires of the same size. The use of a butt connector increases connection safety and durability. Product characteristics:1. The Copper tube splices have an extended entry for easy cable application.The inner dimensions are designed to fit various electrical cables.2. All terminals have control holes.3. Material: Made of seamless copper with high conductivity.4. The surface treatment tin-coated to increase corrosion resistance. 
  Contact Now
Butt connectorsRed, blue and yellow butt connectors provide a simple method of connecting copper cores. They increase connection safety and durability. Complete PVC insulation of the terminal protects from short circuits. For permanent mounting, use a crimp tool with properly selected jaws.
  Contact Now
Product characteristics:1. The Copper tube splices have an extended entry for easy cable application.The inner dimensions are designed to fit various electrical cables.2. All terminals have control holes.3. Material: Made of seamless copper with high conductivity.4. The surface treatment tin-coated to increase corrosion resistance. 
  Contact Now
Butt connectorsRed, blue and yellow butt connectors provide a simple method of connecting copper cores. They increase connection safety and durability. Complete PVC insulation of the terminal protects from short circuits. For permanent mounting, use a crimp tool with properly selected jaws.
  Contact Now
Product characteristics:1.Easy and fast to use, single-tube construction, resistant to water and dirt2.Made of tin coated copper with high conductivity, they provide a strong and durable connection3.High-quality polyolefin heat-shrinkable insulation provides complete terminal integrity4.Transparent outer sleeve enables visual inspection of the connection5.Crimp the terminal and then apply heat to permanently seal the connector
  Contact Now
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring.Features: 1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure.2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
  Contact Now
The JJC-2 piercing clamp is equipped with a tightening torque nut. The screws are treated with corrosion resistance. The torque nut makes installation easier, safer and faster. Its constant piercing pressure can ensure the cable connection to achieve the best electrical effect. The puncture has a waterproof function, and can withstand a voltage of 6kv in water without breakdown.
  Contact Now
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring. Features:1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure. 2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
  Contact Now
The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match. It is used for the branch connection of insulated cables in building power distribution systems, the connection of low-voltage overhead insulated cables, the branch connection of low-voltage insulated incoming cables, and the street lamp power distribution system. Features:1. Main branch: 1.5-25sqmm2.
  Contact Now
The JJC-2 piercing clamp is equipped with a tightening torque nut. The screws are treated with corrosion resistance. The torque nut makes installation easier, safer and faster. Its constant piercing pressure can ensure the cable connection to achieve the best electrical effect. The puncture has a waterproof function, and can withstand a voltage of 6kv in water without breakdown.
  Contact Now
Applications 1.Tensile clamps for OPGW optical cables are mainly used to connect optical cables with a breaking strength of 160kN and below to tensile poles, corner poles and terminal poles. The complete set of OPGW optical cable strain clamp includes outer pre-twisted wires, inner pre-twisted wires, supporting connectors and grounding wires.
  Contact Now
ADSS optical fiber cable insulation wedge clamp is a kind of ADSS optical cable clamp. Mainly used for optical cables with 6-9mm cable diameter. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 173×65×40mmUnit weight:190gCarton size: 550×410×250mmQuantity per carton : 100 piecesMaterial: Nylon and stainless steelCable diameter: 6-9mm Installation image: 
  Contact Now
U type bow shackle mostly used for the ADSS cable installation, which be compatible with tension screws. There are M12 or M14 two types for 40kN shackles, and all will be hot dip galvanized steel.Model No.: U-4Bolt size: M12& M14Drawing: Installation image(part 4) : 
  Contact Now
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
  Contact Now
The WS-type bowl head hanging plate produced by our company has the characteristics of oxidation resistance, corrosion resistance, and durability. It is suitable for the connection between the insulator string and the fittings, the line clamp and the insulator string, and the lightning protection wire and the pole tower. The main body is made of malleable cast iron, hot-dip galvanized, oxidation-resistant and corrosion-resistant.
  Contact Now
Features: 1. It has all the functions of a single suspension clamp.2.
  Contact Now
FTTH drop cable fisher screw eye is installed on the bracket, used to connect and fix the S fixing piece. The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
  Contact Now
The OPGW grounding clamp consists of a section of aluminum alloy wire, an aluminum alloy clamp (connected to the OPGW optical cable), and all-aluminum terminal blocks (connected to the main material of the iron tower).
  Contact Now
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
  Contact Now
Hook bolt made of Q235B galvanized steel, with good high strength mechanical strength, long term usage in optical fiber cable installation, FTTH networks and aerial ADSS accessories.Technical property:1. performance class:4.6 2. The nominal tensile strength of the bolt material reaches 400Mpa3. The yield ratio of the bolt material is: 0.64. The nominal yield strength of the bolt material is up to 400×0.6=240MPa 
  Contact Now
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
  Contact Now
ADSS preformed tension set , single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Composition: inner rods, helical guy grip, thimble clevis, U shackle, extension ring, etc.Product parameter According to different needs, the configuration intensity is 70kNSn Model No.
  Contact Now
The power distribution cable tie is equipped with rubber pads to provide anti-wear function. The state line is not equipped with rubber pads and is not sandblasted. Since there are rubber pads to provide buffering around the wire, the abrasion of the contact surface between the wire and the insulator is avoided. Therefore, the power distribution cable can provide better protection to the wires, and the installation is easier and faster.
  Contact Now
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
  Contact Now
Relate News
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
The standard plywood crates customized based on requirements of customers and loaded in the container.
Electricity is the most indispensable energy source in our lives. Without it, our lives will fall into a mess, and it is the high-voltage wires that ensure that the electric energy reaches our living places safely. In the past, when technology was not so advanced, wires were pulled from the sky to every household, so many small counties still have many cables between houses. In cities, more are buried underground, which can be more secure. However, in many heavy industrial areas, high-voltage wires still need to be passed through high-altitude.
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.